
VUSWM ultrasonic water meter
The NB IoT Box MICRO is built into the meter at the factory. The meter records hourly values and sends them directly over NB-IoT, without a gateway.
NB IoT Box MICRO
The NB IoT Box MICRO is a communication module for integration in meters, sensors and controllers made by device manufacturers.
The host device hands over readings or states via a serial TTL interface (3.3 V), for example using Modbus RTU, ASCII or a customer-specific protocol. The NB IoT Box MICRO stores the data and transmits it over the NB-IoT mobile network to VERILOG or an existing data acquisition system.
Transmission is periodic or event-driven. No gateway and no private radio network is required.
Power comes from its own battery or, depending on the project, from the host device.
12345The NB IoT Box MICRO is built into the host device as a circuit board and connected to its microcontroller via the TTL interface. Antenna, mounting position and power supply are defined in the integration project.
Mobile radio to LTE Cat-NB2 in licensed spectrum. Transmission via MQTT or CoAP, payload additionally encrypted with AES-128 or AES-256.
Four holes for fixing the board in the host device. Mounting and antenna position are agreed per project.
50 × 35 × 5 mm, approx. 50 g. Dimensions can be adapted depending on the version.
As a plastic nano SIM card or as a soldered SIM chip.
Connects the battery. When powered from the host device, the supply is provided per project.
Shown: NB IoT Box MICRO circuit board, top side.
Connecting a meter, sensor or controller to the mobile network takes more than the radio alone. The NB IoT Box MICRO brings these parts ready-made, so you can focus on what your product actually does.
Your device measures as before. The NB IoT Box MICRO takes care of what happens to the values next:
Your device’s microcontroller passes measured values or states to the NB IoT Box MICRO, using Modbus RTU, ASCII or your own protocol.
The NB IoT Box MICRO stores the values until they have been sent. When reception is weak, it sends less often and transmits the stored values in one go.
Data is sent cyclically or on an event, directly over the mobile network. You need neither a gateway nor a radio network of your own.
The values arrive in the VERILOG web portal, with history and limit alarms, or in your HES, MDM or ERP system.
The board is 5 mm thin and weighs about 50 g. That leaves room for it even in devices that were never designed for a radio.

Every integration is a project of its own, because space, data and power supply differ from device to device. These are the steps we take with you:
What data does your device deliver, over which protocol, and how often should it be sent? Plus the available space and the power supply.
Dimensions, mounting position and antenna position are defined for your device. If it delivers analogue or digital signals instead of serial data, an expansion board is added.
Your device’s microcontroller is connected to the NB IoT Box MICRO via TTL. Transmission interval, events and target system are configured.
Configuration and firmware updates are done remotely, even for devices already installed at your customers’ sites.
Tell us about the space, interface and power supply of your device. We will tell you whether the NB IoT Box MICRO fits and which version makes sense.
Phone +43 732 386361-0The NB IoT Box MICRO receives your device’s data via TTL at microcontroller level. For devices without a serial output, there are expansion boards.
They connect to the NB IoT Box MICRO and turn analogue and digital signals into values that the NB IoT Box MICRO transmits.


Guide value with periodic transmission and the best coverage level (ECL 0). With weaker reception the module repeats transmissions, which costs energy. The NB IoT Box MICRO therefore measures its own consumption, calculates the expected battery life from it and adjusts how often it sends.
Mark at 10 years: guide value with periodic transmission and ECL 0. In the VUSWM ultrasonic water meter the battery is designed for two calibration periods.
If the NB IoT Box MICRO is powered by your device, which is possible on a project basis, there is no battery to change at all.
| Interface | 1 × TTL at MCU level (3.3 V) |
|---|---|
| Protocols | Modbus RTU, ASCII or customer-specific |
| Installation | For integration into existing devices and controllers |
| Retrofit | Meters with pulse output |
| Expansions | Analogue expansion for 2 current sensors 0/4 to 20 mA; expansion with 2 digital and 2 analogue inputs 0 to 3.9 V or 0 to 10 V DC |
| Technology | NB-IoT based on LTE Cat-NB2, licensed spectrum |
|---|---|
| Protocols | MQTT or CoAP |
| Encryption | Payload additionally encrypted with AES-128 or AES-256 |
| Transmission | Cyclic or event-driven, configurable |
| Infrastructure | No gateway or concentrator required |
| Remote maintenance | Remote configuration and remote firmware updates |
| Supply | Battery; power from the target device possible on a project basis |
|---|---|
| Battery life | 10+ years with periodic transmission (ECL 0), guide value |
| Energy management | Dynamic, ultra-low-power operation |
| Dimensions | 50 × 35 × 5 mm, variable depending on version |
|---|---|
| Weight | approx. 50 g |
| Protection class | IP68 |
| Temperature range | −25 °C to +60 °C in operation |
| Mounting position | According to the target device; antenna position agreed per project |
| Operation | Servers of VERAUT GmbH in Linz, Austria |
|---|---|
| Analysis | VERILOG web portal: history, limit alarms, export |
| Export | CSV, XLSX, JSON |
| Integration | Data transfer to HES, MDM and ERP systems |
These figures apply to the module. The version for your device is defined in the integration project.
Dust-tight and watertight, even when permanently submerged.
−25 °C to +60 °C.
NB-IoT (LTE Cat-NB2) runs on the mobile network operators’ frequencies. Your device uses their network.
VERAUT builds the NB IoT Box MICRO into one of its own series products: the VUSWM ultrasonic water meter. That is where the module shows what it does in the field.

The NB IoT Box MICRO is built into the meter at the factory. The meter records hourly values and sends them directly over NB-IoT, without a gateway.

If there is no hourly interval without consumption within 24 hours, VERILOG raises an alarm. The municipality checks each message and informs the household concerned.
Read the case
17 large water meters from DN 80 to DN 100 with integrated NB IoT Box MICRO have transmitted hourly and without gaps to VERILOG since 2024.
Read the caseYes. Configuration and firmware updates of the NB IoT Box MICRO are done remotely, even once your device is installed at a customer’s site.
NB-IoT has a high radio reserve and is therefore suited to basements and shafts. What matters is the antenna position inside the device; it is agreed in the project.
If you use VERILOG, your data is stored on servers of VERAUT GmbH in Linz, Austria, in compliance with the GDPR. Alternatively, the data goes directly to your own system.
The NB IoT Box MICRO is a module for building into your own product. If you want to retrofit existing meters without developing a device, choose the NB IoT Box LITE for pulse and encoder meters or the NB IoT Box MINI for complete stations.
The first conversation is also step 1 of the integration project: we clarify the data, space and power supply of your device.
Briefly describe your application, meter type, installation site and hazardous area zone. We reply within up to three working days.
VERAUT GmbH · Derfflingerstraße 14/C/3 · 4020 Linz, Austria
+43 732 386361-0 · info (at) veraut.com