Enquiry

NB IoT Box GPS

Recording position, movement and engine running time of mobile machines and containers.

The NB IoT Box GPS is a battery-powered data logger for locating construction machinery, trailers, containers and other mobile assets.

The device determines its position via GPS/GNSS, detects movement with built-in motion sensing and uses the alternator’s W signal to record whether the engine is running. The data is transmitted over the NB-IoT mobile network to VERILOG or an existing data acquisition system.

Transmission takes place at the set interval and on events, for example when a defined area is left. No connection to vehicle power and no gateway is required.

  • GPS/GNSS
  • Engine time via W signal
  • IP67, potted IP68
W signal NB IoT Box GPS GPS/GNSS NB-IoT VERILOG or your system
NB IoT Box GPS - open housing with radio and GNSS module1234

The NB IoT Box GPS in detail

Positioning, motion sensing, radio and power supply are housed in one weatherproof enclosure. The image shows the opened housing.

  1. 1

    NB-IoT radio module

    Transmission over NB-IoT (LTE Cat-NB2) via MQTT or CoAP, payload additionally encrypted with AES-128 or AES-256.

  2. 2

    GNSS module

    Positioning via GPS/GNSS. The position is sent with every data record; the interval is configurable.

  3. 3

    Cable gland

    Cable entry for the alternator’s W signal and the serial TTL interface.

  4. 4

    Housing

    Weatherproof, IP67; potted version IP68. Operation from −25 °C to +60 °C.

From the machine to the map in four steps

Construction machines, trailers and containers keep changing location. Without tracking, people go looking for them, and whether a machine is actually used only shows up late. The NB IoT Box GPS is attached to the machine and then works on its own:

  1. 1. Capture

    Position, movement, engine

    The box determines its position via GPS/GNSS, a sensor detects movement, and the W signal tells it whether the engine is running.

  2. 2. Buffer

    Nothing gets lost

    The box stores the values. Anything that cannot get through while there is no reception is sent later.

  3. 3. Transmit

    Over NB-IoT, no gateway

    Data is sent at the set interval and also as soon as an event occurs. Directly over the mobile network, with no radio network of your own.

  4. 4. Use

    On the map in VERILOG

    In the VERILOG web portal every machine appears on the map, with history and alarms. The data can also go to your HES, MDM or ERP system.

The map shows where every machine is

The position is part of every data record the box sends. VERILOG uses it to build the map with each machine’s route.

  • Position interval: freely adjustable, depending on how closely you want to follow the route
  • Movement: if a parked machine starts to move, the sensor in the box detects it
  • Areas: when a machine enters or leaves a defined area, an alert goes out immediately
Defined area parked Movement detected Position at set interval Area left:instant alert last position

Is the engine running? The W signal tells you

An engine’s alternator outputs a signal at its terminal W that depends on engine speed. When the engine is off, there is no signal. The box picks up this signal on a dedicated input.

  • Whether the engine is running: on or off, for each machine
  • How long it runs: the running time over the day
  • Where it runs: together with the position, you see where a machine is working and where it is just standing
W signal (terminal W) Engine off Idling Under load Engine off Engine running Running time Time

Is the NB IoT Box GPS right for your machines?

Tell us the machine type, the area of operation and how often you need the position. We will tell you which version and which power supply fit.

Phone +43 732 386361-0
Request a pilot project

Positioning, sensor and engine in one device

Positioning and the motion sensor are built in. From outside, only the W signal and, if needed, one more device on the serial interface are connected.

Built in

  • PositioningGPS/GNSS module, position in the data record
  • MovementIntegrated motion sensor

Connections

  • W signalSpeed-dependent signal from the alternator, terminal W
  • Serial1 × TTL for one more device, for example for fill level measurement
NB IoT Box GPSlocates, buffers, sends

Transmission

  • CellularNB-IoT, LTE Cat-NB2
  • ProtocolsMQTT or CoAP
  • EncryptionPayload additionally encrypted with AES-128 or AES-256

Target systems

  • VERILOGMap, history, limit alarms
  • Your systemHES, MDM or ERP

Its own power supply: battery or rechargeable battery

up to10years

Guide value with battery, periodic transmission and good reception. With rechargeable battery 5 to 10 years, depending on the application. Position and transmission interval and the number of movement and area alerts have a marked effect on runtime.

Battery life depends on

  • Position interval
  • Transmission interval
  • Number of movement and area alerts
  • Reception at the site

Version and rechargeable battery capacity are defined for your application.

All data at a glance

Positioning and movement
Positioning moduleGPS/GNSS, integrated
Position dataTransmitted in the data record, interval configurable
GeofencingAlert when leaving or entering an area
MovementIntegrated motion sensor
Interfaces
Serial1 × TTL
Other inputsW signal (speed signal from the alternator, terminal W)
Communication
TechnologyNB-IoT based on LTE Cat-NB2, licensed spectrum
ProtocolsMQTT or CoAP
EncryptionPayload additionally encrypted with AES-128 or AES-256
TransmissionCyclic or event-driven, configurable
Remote maintenanceRemote configuration and remote firmware updates
Power supply and operation
SupplyBattery or rechargeable battery; no mains or vehicle power required
Battery lifeBattery up to 10 years (guide value); rechargeable battery 5 to 10 years depending on the application
Energy managementDynamic, ultra-low-power operation
MonitoringWatchdogs and automatic network scan
Mechanics and environment
HousingRugged and weatherproof
Protection classIP67; potted version IP68
DimensionsDepending on version
Weightapprox. 680 g to 1,500 g including battery
Temperature range−25 °C to +60 °C in operation
Platform and data
OperationServers of VERAUT GmbH in Linz, Austria
AnalysisVERILOG web portal: map, history, limit alarms
ExportCSV, XLSX, JSON
IntegrationData transfer to HES, MDM and ERP systems

Built for outdoor use

The box is mounted on the outside of machines, trailers and containers, in rain, dust and cold. The housing is designed for that:

  • IP67 as standard

    Dust-tight and protected against temporary immersion.

  • IP68 in the potted version

    The electronics are potted and protected even when permanently submerged.

  • Operating temperature

    −25 °C to +60 °C.

Where the NB IoT Box GPS is used

Wherever equipment changes location and no power connection is available:

  • Construction machinery: location and engine running time of equipment on changing sites
  • Rental machinery: track whereabouts and usage
  • Trailers and vehicles: position without connecting to vehicle power
  • Containers and tanks: location and, via the serial interface, the fill level too
  • Mobile equipment in utility networks: position and condition of equipment that moves

In practice: Huemer GmbH

Huemer GmbH from Engerwitzdorf, specialised in concrete drilling and sawing, has equipped its fleet with a customised NB IoT Box GPS.

  • 150machines equipped in the first project phase
  • 2 weeksuntil the solution had paid for itself
  • 1machine located in the Czech Republic and recovered

Huemer GmbH, Engerwitzdorf

A machine did not come back from a site. Tracking showed it was in the Czech Republic. It was recovered and returned to the depot. Today the company knows at any time where its machines are and which are working.

Read the case

Documents

Frequently asked questions

Does the box need power from the machine?

No. It runs on its own battery or rechargeable battery. From the machine it only picks up the W signal.

Does it work on equipment without an engine?

Yes. On trailers, containers or tanks the box delivers position, movement and area alerts; the W signal input simply stays unused.

Do I need a gateway or my own radio network?

No. The box sends directly over the mobile network operators’ NB-IoT network.

Can the data go into our own system?

Yes. The box transmits via MQTT or CoAP to your HES, MDM or ERP system. From VERILOG, data can be exported as CSV, XLSX or JSON.

Which NB IoT Box for fixed metering points?

For meters and sensors that stay in one place there are the NB IoT Box LITE, NB IoT Box MINI and NB IoT Box LITE PRESSURE. The NB IoT Box page helps you choose.

Your machines on the map

Tell us which machines and containers you want to track and whether you need engine running time. Together we define areas, intervals and the data path.

Let's talk about your metering point.

Briefly describe your application, meter type, installation site and hazardous area zone. We reply within up to three working days.

VERAUT GmbH · Derfflingerstraße 14/C/3 · 4020 Linz, Austria
+43 732 386361-0 · info (at) veraut.com

What is it about?
0