Enquiry

NB IoT Box MICRO

NB-IoT communication module for integration in meters, sensors and controllers.

The NB IoT Box MICRO is a communication module for integration in meters, sensors and controllers made by device manufacturers.

The host device hands over readings or states via a serial TTL interface (3.3 V), for example using Modbus RTU, ASCII or a customer-specific protocol. The NB IoT Box MICRO stores the data and transmits it over the NB-IoT mobile network to VERILOG or an existing data acquisition system.

Transmission is periodic or event-driven. No gateway and no private radio network is required.

Power comes from its own battery or, depending on the project, from the host device.

  • Module 50 × 35 × 5 mm
  • TTL 3.3 V
  • NB-IoT, no gateway
VERILOG or your system Your device Meter, sensor, controller MCU TTL 3.3 V Modbus · ASCII NB IoT Box MICRO buffers and sends NB-IoT
NB IoT Box MICRO circuit board12345

The NB IoT Box MICRO in detail

The NB IoT Box MICRO is built into the host device as a circuit board and connected to its microcontroller via the TTL interface. Antenna, mounting position and power supply are defined in the integration project.

  1. 1

    NB-IoT radio module

    Mobile radio to LTE Cat-NB2 in licensed spectrum. Transmission via MQTT or CoAP, payload additionally encrypted with AES-128 or AES-256.

  2. 2

    Mounting holes

    Four holes for fixing the board in the host device. Mounting and antenna position are agreed per project.

  3. 3

    Compact design

    50 × 35 × 5 mm, approx. 50 g. Dimensions can be adapted depending on the version.

  4. 4

    SIM card

    As a plastic nano SIM card or as a soldered SIM chip.

  5. 5

    Battery connector

    Connects the battery. When powered from the host device, the supply is provided per project.

Shown: NB IoT Box MICRO circuit board, top side.

Cellular connectivity in your device, without developing the radio yourself

Connecting a meter, sensor or controller to the mobile network takes more than the radio alone. The NB IoT Box MICRO brings these parts ready-made, so you can focus on what your product actually does.

Developing it yourself

  • Design the radio and antenna and prove them in the field
  • Firmware for connection setup and recovery after faults
  • Energy management for years of battery operation
  • Connection to a backend

With the NB IoT Box MICRO

  • Antenna, radio and firmware are matched to each other and proven in the field
  • Three levels of monitoring (watchdogs) restart the radio or module by themselves after a fault
  • Energy management is built in
  • Your device only needs a serial interface

From the microcontroller to the backend in four steps

Your device measures as before. The NB IoT Box MICRO takes care of what happens to the values next:

  1. 1. Hand over

    Data via TTL

    Your device’s microcontroller passes measured values or states to the NB IoT Box MICRO, using Modbus RTU, ASCII or your own protocol.

  2. 2. Buffer

    No values are lost

    The NB IoT Box MICRO stores the values until they have been sent. When reception is weak, it sends less often and transmits the stored values in one go.

  3. 3. Transmit

    Over NB-IoT, no gateway

    Data is sent cyclically or on an event, directly over the mobile network. You need neither a gateway nor a radio network of your own.

  4. 4. Use

    In VERILOG or your system

    The values arrive in the VERILOG web portal, with history and limit alarms, or in your HES, MDM or ERP system.

Fits on 50 × 35 millimetres

The board is 5 mm thin and weighs about 50 g. That leaves room for it even in devices that were never designed for a radio.

  • Dimensions can be adapted depending on the version
  • Mounting position follows your device
  • We agree the antenna position with you so that reception works once the module is installed
NB IoT Box MICRO, circuit board seen from above
50 mm
35 mm
Side view
5 mm

How an integration project runs

Every integration is a project of its own, because space, data and power supply differ from device to device. These are the steps we take with you:

  1. 1
    Clarify

    Define the requirements

    What data does your device deliver, over which protocol, and how often should it be sent? Plus the available space and the power supply.

  2. 2
    Design

    Fix the version

    Dimensions, mounting position and antenna position are defined for your device. If it delivers analogue or digital signals instead of serial data, an expansion board is added.

  3. 3
    Integrate

    Build in and connect

    Your device’s microcontroller is connected to the NB IoT Box MICRO via TTL. Transmission interval, events and target system are configured.

  4. 4
    Operate

    Maintain remotely

    Configuration and firmware updates are done remotely, even for devices already installed at your customers’ sites.

Will the NB IoT Box MICRO fit your device?

Tell us about the space, interface and power supply of your device. We will tell you whether the NB IoT Box MICRO fits and which version makes sense.

Phone +43 732 386361-0
Discuss a pilot project

One serial interface is all it takes

The NB IoT Box MICRO receives your device’s data via TTL at microcontroller level. For devices without a serial output, there are expansion boards.

From your device

  • Serial1 × TTL at MCU level, 3.3 V
  • ProtocolsModbus RTU, ASCII or customer-specific
  • RetrofitMeters with pulse output

With expansion board

  • Current sensors2 × 0/4 to 20 mA
  • Digital and analogue2 × digital input, 2 × analogue input 0 to 3.9 V or 0 to 10 V DC
NB IoT Box MICRObuffers, encrypts, sends

Transmission

  • CellularNB-IoT, LTE Cat-NB2
  • ProtocolsMQTT or CoAP
  • EncryptionPayload additionally encrypted with AES-128 or AES-256

Target systems

  • VERILOGVERAUT web portal for history, alarms and export
  • Your systemHES, MDM or ERP

The two expansion boards

They connect to the NB IoT Box MICRO and turn analogue and digital signals into values that the NB IoT Box MICRO transmits.

Analogue expansion board for two current sensors
Analogue expansionFor 2 current sensors 0/4 to 20 mA.
Expansion board with digital and analogue inputs
Digital and analogue expansion2 digital inputs and 2 analogue inputs 0 to 3.9 V or 0 to 10 V DC.

Runs on its own battery or on power from your device

over10years

Guide value with periodic transmission and the best coverage level (ECL 0). With weaker reception the module repeats transmissions, which costs energy. The NB IoT Box MICRO therefore measures its own consumption, calculates the expected battery life from it and adjusts how often it sends.

Mark at 10 years: guide value with periodic transmission and ECL 0. In the VUSWM ultrasonic water meter the battery is designed for two calibration periods.

Battery life depends on

  • Transmission interval
  • Reception at the installation site
  • Number of event-driven transmissions

If the NB IoT Box MICRO is powered by your device, which is possible on a project basis, there is no battery to change at all.

All data at a glance

Interface and integration
Interface1 × TTL at MCU level (3.3 V)
ProtocolsModbus RTU, ASCII or customer-specific
InstallationFor integration into existing devices and controllers
RetrofitMeters with pulse output
ExpansionsAnalogue expansion for 2 current sensors 0/4 to 20 mA; expansion with 2 digital and 2 analogue inputs 0 to 3.9 V or 0 to 10 V DC
Communication
TechnologyNB-IoT based on LTE Cat-NB2, licensed spectrum
ProtocolsMQTT or CoAP
EncryptionPayload additionally encrypted with AES-128 or AES-256
TransmissionCyclic or event-driven, configurable
InfrastructureNo gateway or concentrator required
Remote maintenanceRemote configuration and remote firmware updates
Power supply
SupplyBattery; power from the target device possible on a project basis
Battery life10+ years with periodic transmission (ECL 0), guide value
Energy managementDynamic, ultra-low-power operation
Mechanics and environment
Dimensions50 × 35 × 5 mm, variable depending on version
Weightapprox. 50 g
Protection classIP68
Temperature range−25 °C to +60 °C in operation
Mounting positionAccording to the target device; antenna position agreed per project
Platform and data
OperationServers of VERAUT GmbH in Linz, Austria
AnalysisVERILOG web portal: history, limit alarms, export
ExportCSV, XLSX, JSON
IntegrationData transfer to HES, MDM and ERP systems

Protection class and operating conditions

These figures apply to the module. The version for your device is defined in the integration project.

  • Protection class IP68

    Dust-tight and watertight, even when permanently submerged.

  • Operating temperature

    −25 °C to +60 °C.

  • Radio in licensed spectrum

    NB-IoT (LTE Cat-NB2) runs on the mobile network operators’ frequencies. Your device uses their network.

Proven in our own meter and with partners

VERAUT builds the NB IoT Box MICRO into one of its own series products: the VUSWM ultrasonic water meter. That is where the module shows what it does in the field.

  • 421VUSWM water meters with NB IoT Box MICRO for the municipality of Fresach
  • 7leaks and unusual consumption detected in the first six months
  • 99.5%transmission rate of the installed meters in Fresach

VUSWM ultrasonic water meter

The NB IoT Box MICRO is built into the meter at the factory. The meter records hourly values and sends them directly over NB-IoT, without a gateway.

Municipality of Fresach

If there is no hourly interval without consumption within 24 hours, VERILOG raises an alarm. The municipality checks each message and informs the household concerned.

Read the case

ViWa GmbH, Cham

17 large water meters from DN 80 to DN 100 with integrated NB IoT Box MICRO have transmitted hourly and without gaps to VERILOG since 2024.

Read the case

Documents

Frequently asked questions

Can the firmware still be changed later?

Yes. Configuration and firmware updates of the NB IoT Box MICRO are done remotely, even once your device is installed at a customer’s site.

Does it work in basements or shafts?

NB-IoT has a high radio reserve and is therefore suited to basements and shafts. What matters is the antenna position inside the device; it is agreed in the project.

Where is the data stored?

If you use VERILOG, your data is stored on servers of VERAUT GmbH in Linz, Austria, in compliance with the GDPR. Alternatively, the data goes directly to your own system.

NB IoT Box MICRO, NB IoT Box LITE or NB IoT Box MINI?

The NB IoT Box MICRO is a module for building into your own product. If you want to retrofit existing meters without developing a device, choose the NB IoT Box LITE for pulse and encoder meters or the NB IoT Box MINI for complete stations.

NB-IoT in your product?

The first conversation is also step 1 of the integration project: we clarify the data, space and power supply of your device.

Let's talk about your metering point.

Briefly describe your application, meter type, installation site and hazardous area zone. We reply within up to three working days.

VERAUT GmbH · Derfflingerstraße 14/C/3 · 4020 Linz, Austria
+43 732 386361-0 · info (at) veraut.com

What is it about?
0