Enquiry

NB IoT Box MINI

One box for the readings of several instruments.

The NB IoT Box MINI records measured values from volume converters, gas and water meters and various sensors. Thanks to its different interfaces, several compatible instruments can be connected to a single data logger. The values are stored and transmitted over NB-IoT at configurable intervals, hourly by default, to VERILOG or an existing data acquisition system. Battery-powered, with no external power supply and no additional gateway.

  • Several instruments
  • NB-IoT
  • ATEX Zone 2
Zone 2 RS485PulseAnaloguePT1000 Gas meter Pressure Temperature Volume converter NB IoT Box MINI Alarm NB-IoT, hourly VERILOG or your system
NB IoT Box MINI data logger, angled view with display and connectors1234

The NB IoT Box MINI in detail

The NB IoT Box MINI is a compact, intrinsically safe data logger for wall mounting in gas and water supply facilities. It uses the same housing design as the VERIBOX-MINI.

  1. 1

    Display and four keys

    Measured values and device status can be read directly on the display. Commissioning and configuration are done via Bluetooth with the VERAUT app.

  2. 2

    Connections for meters and sensors

    Connections for pulse transmitters, encoders, analogue signals, Pt1000 temperature sensors and serial interfaces.

  3. 3

    Antenna connector

    Where mobile reception is limited, for example in pits or steel cabinets, an external antenna can be connected.

  4. 4

    Mounting plate

    For wall mounting; the housing can be sealed against unauthorised opening.

approx. 185 × 135 × 60 mm, approx. 680 g including battery

Several instruments, different interfaces, often no power supply

Gas transfer stations and gas pressure regulating and metering stations often contain several instruments, such as gas meters, volume converters, pressure sensors and temperature sensors. In water supply facilities, meter readings, line pressures and reservoir levels need to be recorded. At remote metering points in particular, a power supply is not always available. Connecting each instrument separately to remote transmission increases installation and maintenance effort.

Today

  • Manual reading or separate data transmission infrastructure
  • Additional interface converters for certain volume converters
  • External power supply or solar panel at the metering point

With the NB IoT Box MINI

  • Several existing instruments on one shared data transmission unit
  • Direct reading of supported volume converters via serial interfaces
  • Battery-powered data acquisition with direct NB-IoT transmission, no additional gateway

How measured values are recorded, stored and transmitted

The NB IoT Box MINI is mounted at the intended location and connected to the existing instruments. It reads the supported values and transmits them over NB-IoT to the target system of your choice.

  1. 1. Measure

    Record values from different instruments

    Volume converters are read via the serial interfaces. Inputs are available for meters with pulse output or encoder. Pressure and level sensors can be connected to the analogue inputs and suitable temperature sensors to the Pt1000 input.

  2. 2. Store

    Storage with time stamp

    Measured values are stored with a time stamp in the internal memory, for example at an hourly recording interval. The configured limit values are checked continuously.

  3. 3. Transmit

    Transmission over NB-IoT

    By default, values are transmitted once an hour over NB-IoT. The transmission interval is configurable. If the radio connection is interrupted, buffered values are sent once it is restored, with their original time stamps.

  4. 4. Use

    Values and alarms

    In VERILOG or your HES, MDM or ERP system. Limit violations, relevant events and device faults are reported to the central system. If configured, alarm messages can be forwarded by e-mail.

Connect several instruments to a single data transmission unit

The following application examples show which instruments can be connected to the NB IoT Box MINI and which inputs are intended for them. Thanks to its various interfaces, different types of instrument can share one data transmission unit.

Gas transfer stations and gas pressure regulating and metering stations

  • Volume converterRS232 / RS485
  • Gas meter with pulse outputDigital input
  • Pressure transmitterAnalogue input
  • Temperature sensorPT1000
one NB IoT Box MINI

Meter readings, stored load profile values and status information can be read directly via the supported serial interface of the volume converter.

Water meters and level measurement in water supply facilities

  • Water meterPulse or encoder
  • Level probeAnalogue input
  • Pressure sensorAnalogue input
  • Local signalSwitching output
one NB IoT Box MINI

Regular recording of consumption values makes unusual changes in consumption visible early. These can indicate a leak, for example.

Heat transfer stations (district heating)

  • Heat meterRS485, Modbus
  • Temperature sensorPT1000
  • Further signalsAnalogue input
one NB IoT Box MINI

Recording of heat quantities at heat transfer stations via supported Modbus interfaces or analogue signals.

Level monitoring in hazardous areas

  • Level sensorAnalogue input
  • Limit alarm via digital outputSwitching output
one NB IoT Box MINI

The level is recorded by a connected sensor. When a configured limit is reached, an alarm signal can be triggered.

Is the NB IoT Box MINI suitable for your metering point?

Tell us which instruments are to be connected, which Ex zone classification applies at the installation site and what the NB-IoT coverage is like there. We check whether one NB IoT Box MINI is sufficient for the intended instruments and which interfaces can be used.

Phone +43 732 386361-0
Send enquiry

Inputs and outputs at a glance

The NB IoT Box MINI has digital inputs for pulse signals, encoder interfaces, analogue inputs and serial interfaces. Two digital outputs are available for local switching and alarm functions.

Inputs

  • Digital inputs4 digital inputs for pulse transmitters, reed contacts, S0 and NAMUR signals
  • EncoderSCR and SCR+ absolute encoders, Gray-code registers
  • Analogue inputs3 × 0 to 10 V and 0 to 20 mA
  • TemperaturePT1000
  • SerialRS232, RS485 and TTL; Modbus RTU and ASCII

Outputs

  • Digital outputs2 × for switching and alarm functions on site
NB IoT Box MININB IoT Box MINIrecords, stores and transmits values over NB-IoT

Transmission

  • RadioNB-IoT, LTE Cat-NB2
  • ProtocolsMQTT(S) or CoAP(S) over TLS, payload AES-encrypted
  • AntennaInternal antenna; external antenna via FME where mobile reception is limited

Target systems

  • VERILOGVERAUT’s web portal
  • Existing data acquisition systemsHES, MDM or ERP

Volume converters it reads directly

Via the serial interface the NB IoT Box MINI reads meter readings, load profiles and status straight from the device, without a converter. Other makes and protocols on request.

  • Honeywell / ElsterEK260, EK280
  • ItronCorus, Evo+
  • RMG / KamstrupTME-400
  • Instromet444, 999
  • SICKFlowsick
  • DresserMicroSeries
  • American MeteriMeter
  • FlonidanUniFlo
  • PlumMacBat
  • ElgasElcor

Hourly data transmission with a battery life of over 10 years

over10years

Guide value for hourly transmission and good reception (ECL 0). The internal lithium primary battery powers the NB IoT Box MINI. No external power supply is needed for the intended operation.

Battery life depends on

  • Mobile reception at the installation site
  • Transmission interval
  • Temperature

If the metering point is in a pit or steel cabinet, an external antenna improves reception. Better reception can reduce the energy needed for each transmission and extend battery life.

How transmission interval and reception affect battery life →

Technical data of the NB IoT Box MINI

Inputs and outputs
Digital inputs4 × pulse, reed, S0 or NAMUR
EncoderSCR and SCR+ absolute encoders, Gray-code registers, NAMUR
Analogue inputs3 × 0 to 10 V DC and 0 to 20 mA
TemperaturePT1000
SerialRS232, RS485 and TTL; Modbus RTU and ASCII
Digital outputs2 × switching and alarm function
Communication
TechnologyNB-IoT, LTE Cat-NB2 (3GPP Rel. 13/14), licensed spectrum
ProtocolsMQTT(S) or CoAP(S) over TLS
EncryptionPayload with AES-128 or AES-256
AntennaInternal; external via FME
Transmission intervalFreely configurable, hourly by default
ConfigurationOn site via Bluetooth with the VERAUT app (Android, Windows); remote configuration and firmware updates
Data and alarms
Load profileHourly storage of measured values (24 points per day)
Buffering during communication failureLocal memory, automatic resend with timestamp
AlarmsLimit, event and device alarms
Alarm routingBackend, forwarding by e-mail
Explosion protection
MarkingEx ib IIC T4 Gb
ZonesApproved for Zone 2; Zone 1 approval in progress
HydrogenHydrogen-capable version: approval in progress
StandardsEN 60079, CE marking
Power and environment
Power supplyLithium primary cell, no mains connection
Battery lifeGuide value over 10 years with hourly transmission and ECL 0
Operating temperature−20 to +60 °C
Operating modeEnergy-optimised, battery-powered operation
Mechanics
Dimensionsapprox. 185 × 135 × 60 mm
Weightapprox. 680 g including battery
HousingSealable industrial housing
MountingWall mounting

Explosion protection for use in Zone 2, extension to Zone 1 in the approval process

The ATEX Directive 2014/34/EU sets requirements for equipment and protective systems intended for use in potentially explosive atmospheres. The NB IoT Box MINI is designed with the type of protection intrinsic safety. The electrical parameters of the intrinsically safe circuits are limited so that no effective ignition source arises under the specified conditions. No additional flameproof Ex enclosure is required for use in accordance with the approval.

Zone 2 · approved

An explosive gas-air mixture does not occur in normal operation, or only briefly.

Zone 1 · approval in progress

An explosive mixture can occur occasionally in normal operation.

The marking, part by part

  1. ExExplosion protection
  2. ibType of protection: intrinsic safety
  3. IICGas group IIC, includes IIA and IIB
  4. T4Surface no hotter than 135 °C
  5. GbEquipment protection level b, designed for Zone 1
  • Hydrogen

    A version for hydrogen-containing gases is in the approval process.

  • Sealable housing

    The housing can be sealed against unauthorised opening.

  • Standards

    EN 60079 for explosion protection, CE marking.

  • Governing documents

    For the selection, installation and use of the device in hazardous areas, the valid approval documentation, the operating instructions and the conditions of use set out in them apply.

Proven housing design with new NB-IoT electronics

The NB IoT Box MINI uses the proven housing design of the VERIBOX-MINI combined with newly developed NB-IoT electronics.

Regional gas network operator

At gas transfer and metering points, the existing volume converters are read over NB-IoT without additional gateway infrastructure. Result: no gateway infrastructure of its own had to be built; recorded load profile values are buffered and transmitted to the central data acquisition system.

Documents

Frequently asked questions

NB IoT Box MINI or VERIBOX-MINI?

Inputs and outputs are the same; the radio path differs. The NB IoT Box MINI transmits hourly over NB-IoT by default; battery life is over 10 years (guide value at hourly transmission and ECL 0). The VERIBOX-MINI transmits over 4G/LTE with automatic switching to 3G or 2G where available, typically once a day, with up to 6 years of battery life. It is already approved for Zone 1 and 2. If you need Zone 1 right away, the VERIBOX-MINI is the right choice.

How is the NB IoT Box MINI commissioned?

On site via Bluetooth with the VERAUT app for Android and Windows. Later changes and firmware updates are made remotely.

Only one meter is installed at my metering point. Is the NB IoT Box MINI suitable?

For a single meter with pulse or encoder output, the more compact NB IoT Box LITE is intended; for pressure measurement only, the NB IoT Box LITE PRESSURE.

What is a volume converter?

A device on gas meters that converts the measured gas volume to standard volume using pressure and temperature. It is the basis for billing.

Let us check your metering point together

Together we review the existing meters, volume converters and sensors and the connections required, and prepare a suitable proposal for data acquisition and transmission. You will learn whether one NB IoT Box MINI is enough, which values can be recorded and which transmission intervals are possible.

Let's talk about your metering point.

Briefly describe your application, meter type, installation site and hazardous area zone. We reply within up to three working days.

VERAUT GmbH · Derfflingerstraße 14/C/3 · 4020 Linz, Austria
+43 732 386361-0 · info (at) veraut.com

What is it about?
0